ISO 5725-2 PDF
Buy PN ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 2: BASIC METHOD FOR THE. Buy NBR ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 2: BASIC METHOD FOR. DS/ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 2: BASIC METHOD FOR THE.
|Published (Last):||3 February 2005|
|PDF File Size:||12.83 Mb|
|ePub File Size:||16.41 Mb|
|Price:||Free* [*Free Regsitration Required]|
One laboratory re- sult was identified as a straggler; it originated from the same laboratory Lab. To request this FREE document, please email us.
BS ISO 5725-2:1994
Further regular testing is required to show that the labora- tory bias does not vary; the method described in IS0 may be used for this. The boxed points in figures B.
Amplifies the general principles to be observed in designing experiments for the 5275-2 estimation of the precision of measurement methods by means of a collaborative interlaboratory experiment, provides a detailed practical 57252- of the basic method for routine use in estimating the precision of measurement methods, provides guidance to all personnel concerned with designing, performing or analysing the results of the tests for estimating precision.
The purpose of the two-bottle system was to confirm the absence of the between-bottle variation. All measurements are to be carried out according to that standard method.
Comparison of the trueness of two measurement methods is considered in IS0 The faster, easier way to work with standards. IS0 l should be read in conjunction with all other parts of IS0including this part, because it gives the underlying definitions and general principles.
The test results ieo each 57255-2 are shown in figures B. Ministry of Commerce and Industry. Al- though, for some measurement methods, the true value cannot be known exactly, it may be possible to have an accepted reference value for the property being measured; for example, if suitable reference materials are available, or if the accepted reference value can be established by refer- ence to another measurement method or by preparation of a known sample.
In this report the following information shall be given: Bias can arise, for example, in 57225-2 analysis if the measurement method fails to extract all of an element, or if the presence of one element interferes with the determination of another.
GSO ISO – Standards Store – GCC Standardization Organization
You can buy this standard from any national standardization body. You may find similar items within these categories by selecting from the choices below:. Use in practice of accuracy values.
It is not applicable if the bias in the measurement of one property is affected by the level of a second property i. Annexes B, C and D are for information only.
Thus results from each laboratory can be considered as replicates under repeatability conditions. Prior to conducting the as- sessment of trueness, a check of the precision of the standard measurement method as applied by the lab- oratory shall be performed. It may appear that some laboratories did not use the required equipment or did not work ac- cording to the specified conditions.
If so, what are the improvements required? Basic method for the determination of repeatability and reproducability of a standard measurement method. The first condition is actually developed in 4. When gR is larger than T. The number of laboratories to be used is discussed in io 6.
In the former case, the repeatability standard devi- ation, gr, and the reproducibility standard deviation, gR, will be used for the assessment of the trueness of the measurement method. Relevant International Standards on sample division should be consulted. Accuracy trueness and precision of measurement methods and results – Part 1: The laboratory bias is further considered in IS0 The uncertainty in the estimate of the laboratory bias depends on the repeatability of the measurement method and on the number of test results obtained.
Company organization, management and quality.
ISO Accuracy of measurement methods and results-Part 2 Basic method – MBA智库文档
Analysis of the results showed that the between- bottle variation was indeed insignificant; the sample was considered to be homogeneous. As a result the experiment may have to be repeated to yield the expected preci- sion values.
Outliers and stragglers Level Lab. In particular, if outlying values are de- tected, all necessary steps shall be taken to investi- gate the reasons why they have been obtained, including re-appraisal of the suitability of the accepted reference value. Your basket is empty. They contain a digital watermark to protect the copyright. Take the smart route to manage medical device compliance. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
Annex B provides practical examples of estimating the precision of measurement methods by experiment. Reference materials shall be homogeneous.