IBANEZ S520EX MANUAL PDF

The SEX is an S series solid body electric guitar model introduced by Ibanez in It was initially produced in Korea and then later in Indonesia. There’s no way a guy who does a couple guitar setups every day of the year would do a better than someone will with instructions from the. For over 18 years, Ibanez RG guitars with Edge double locking sys- tems have been SEX MOF. • 3pc Wizard II Manually Adjustable Zero. Point System.

Author: Kazrale JoJom
Country: Kazakhstan
Language: English (Spanish)
Genre: Medical
Published (Last): 6 January 2007
Pages: 369
PDF File Size: 16.8 Mb
ePub File Size: 11.13 Mb
ISBN: 945-7-65341-159-2
Downloads: 98335
Price: Free* [*Free Regsitration Required]
Uploader: Akinotaur

Insert the tremolo arm into the arm socket and firmly push down until the arm snaps into place. To change the strings angle adjust the two 2mm 6 screws on the highside of the bridge, chanding the pivot angle. If the 12th fret harmonic is higher than the fretted note, the saddle needs to be moved forward. The truss rod is adjustable at the headstock using as allen wrench or an adjustment wrench. Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the String holder block 4.

Adjust the saddle forward or backward to the proper position and tighten the saddle lock down screw. If lower than standard settings are desired, this can often result in”buzz” or “rattle” of the strings.

To further reduce the torque, remove both bushings. If the 12th fret is sharper than the open note, the saddle needs to be moved back. Turn the notched wheel 4 To raise or lower the bridge. Wind the string around the tuning machine and tune to pitch. Tighten the String stopper Screw. Always loosen the Stud lock screws counter clockwise with a 1. The tremolo arm is placed in the hole in the bridge plate and inserted into the threaded block.

  JORGE LUIS BORGES EL ZAHIR EN EL ALEPH PDF

Solid Body Electric Guitars. Tighten the string stopper bolt. Wind the string around the tuning machine and tune to pitch 6. Raise or lower the tremolo to the desired string height using a 4mm allen wrench.

S520EX (2005–2009)

Tighten the Stud lock screw 3. The height adjustment of the tremolo can be set by using the two 3mm adjustment screws on either side of the tremolo unit.

Tune the guitar to pitch and recheck the intonation. If the intonation is still not correct repeat steps 2 and 3. When the guitar is properly adjusted, tighten the top lock pressure pad screws 5.

The Overall Tremolo height can be adjusted by raising or lowering the Height Adjustment screws 5 on either side of the bridge. Over adjustment can result in damage to the instrument and will no be covered under warranty.

Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips 2. Thread the new string through the string holder tubeand over the saddle pulling it tight towards the headstock. To remove the tremolo arm, firmly hold the arm at the break over point bend and pull up until the arm is released. Turn the Arm torqueadjustment nut turns counter clockwise.

On the bass plate there are two holes for each saddle lock down screw. Make sure the truss kbanez is properly adjusted before adjusting the action. If the 12th fret is flatter than the open note, the saddle needs to be moved forward. To adjust the string height of the saddles use a 1. Adjusting the String Height. The height adjustment of the tremolo can be set by using the two 4mm s520rx screws 2 on either side of the tremolo unit.

Adjust a520ex saddle forward or backward to the proper position and ibanfz the Saddlelock down screw 9. Raise or lower the tremolo to the desired string height using a 3mm allen wrench. Only loosen the screw enough to move the saddle. Insert the tremolo arm into the arm socket and turn the Arm torque adjustment nut A clockwise until it stops. Wlnd the string around the tuning machine and tune to pitch.

  ERCOFTAC BEST PRACTICE GUIDELINES PDF

If the 12th fret harmonic pitch is lower than the fretted note, the saddle needs to be moved back. Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the string holder block.

Wiring Diagrams

Ibanea For ease in retuning. TZ Bridges The Overall Tremolo height can be adjusted by raising or lowering the Height Adjustment screws 5 on either side of the bridge. Height adjustment of the individual strings can be adjusted by useing a 1.

Loosen the pressure pad lock screws on the top lock with a 3. The purpose of this is to accommodate for different tunings or different gauges of strings. All guitar necks are subject to great stress as a result of string tension, humidity or changes in climactic conditions. This is caused by the string vibrating.

SEX (–) | Ibanez Wiki | FANDOM powered by Wikia

Open the new bushings at the split section and snap them into place on the tremolo arm. Intonation adjustment is usually necessary when new strings are fitted it can also be affected by the angle of the tremolo unit.

All lbanez guitars use A for a standard pitch. Tighten the s5200ex pad screws. Before adjusting the intonation, first determine the direction that the saddle needs to be moved. To allow the arm to swing freely.

No Comments

Categories: Politics