FBI XL2T PROGRAM PDF

Introduction The XL-2T is a state of the art microprocessor-based control/ communicator. The system features seven (7) fully programmable zones. Programming. XL-2T. Security System. Installation and Setup Guide. STAY. INSTANT. ACYLB. READY APPENDIX D – SYSTEM PROGRAMMING WORKSHEET. Example: To program phone number enter 1#8#0#0# etc. Exit Program STAY. Default Panel Short “EEPROM RESET” pins on panel and power up system.

Author: Gall Zolorr
Country: Djibouti
Language: English (Spanish)
Genre: Video
Published (Last): 26 February 2018
Pages: 25
PDF File Size: 14.7 Mb
ePub File Size: 20.74 Mb
ISBN: 588-5-42947-906-5
Downloads: 38863
Price: Free* [*Free Regsitration Required]
Uploader: Gulrajas

Page of 93 Go. Question 11, L1 – Exit Delay By pressing ‘print’ button you will print only current page. The door of the metal cabinet may be removed to make it easier to install the control panel. Section 5 – System Operations 4.

Xlt2 double-gang box shall be mounted flush with wall in order for keypad screws to fit. Upon detection of the first violation, smoke detector power on conventional 4 wire smoke detectors connected to ZONE modules will be reset for a period of 8 seconds. There are 36 total questions, with multiple data entry locations. Next, enter the desired account number each digit followed by the key.

FBII XL-2T Installation And Setup Manual

The keypad sounder annunciates differently to indicate the following conditions: How can i change or get rid of this 3 digit code. I then pressed code button followed by master codethen user no 3 and then new 4 digit user code. I pressed the code button ready light did not flashthen pressed both 7 and 9 at same time, to reset master code to Create an opening and mount a standard double-gang box. Keypad Sounder Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system.

  HANS JENNY CYMATICS PDF

This equipment generates and uses radio frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer’s instructions may cause interference to radio and television reception.

For UL installations see wiring diagram for hookup.

FBI XL-2T Turbo Program Sheet

Don’t show me this message again. Section 5 – System Operations User Deletion User codes can be deleted directly through the keypad. The system features seven 7 fully programmable zones. LCD display keypads will indicate the following message: Directly to a single or double gang electrical junction box.

FBI XL-2 Program Sheet

To print the manual completely, please, download it. Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to xl2r condition of the security system. Page 23 Fire Trouble is reported to the CS if enabled program question 32, location 3. Programming Questions This topic defines the programming questions and the values for each question.

The system contains up to fifteen user codes 4 digits each with the following applications: Fire Trouble is reported to the CS if enabled program question 32, location 3. A user code is required to ;rogram the system.

Replacement microprocessors are available through Technical Support or Customer Service. See the following diagram: Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: The system will report all signals to the primary receiver phone number.

  EXULTET LATIN PDF

After this time period, power is restored.

It is time to change code for security reasons. The restore code will also be reported if the system is disarmed during an alarm. On LED keypads the sounder will beep after each entry. Some new features have been added and others have been modified.

If the siren is already sounding, the supervision will not take effect until after bell cutoff time. The keypads can be surface mounted or flush mounted as described below.

Page 40 Section 5 – System Operations If a user code is not required to set the time, then enter: Separate the two halves of the keypad by placing a straight-slot screwdriver into one of the two slots at the bottom of the keypad and twisting. The checkmark highlights which options are selected.

The rear plastic mounting plate is not used for recessed installations. With this device some systems can obtain dial tone in areas which do not automatically provide dial tone. Upon entry to the system log view, LCD based keypads will show the events one at a time starting from the progra, event.

Question 32, L1 – Bypass Code Proceed to question 02 through the sequence Refer to the Installation Instructions for hookup information.

No Comments

Categories: Technology