DIN EN ISO 7253 PDF

Buy DIN EN ISO PAINTS AND VARNISHES – DETERMINATION OF RESISTANCE TO NEUTRAL SALT SPRAY (FOG) from SAI. DIN EN ISO Paints and varnishes – Determination of resistance to neutral salt spray (fog) (ISO ); German version EN ISO Draft standard [WITHDRAWN] DIN ISO – Draft. Paints and varnishes – Determination of resistance to neutral salt spray (fog) (ISO.

Author: Tygoshicage Malarn
Country: Spain
Language: English (Spanish)
Genre: Health and Food
Published (Last): 21 May 2007
Pages: 272
PDF File Size: 19.41 Mb
ePub File Size: 2.83 Mb
ISBN: 314-1-69484-908-8
Downloads: 46140
Price: Free* [*Free Regsitration Required]
Uploader: Vizuru

Assessment of degree of flaking ISO Assessment of degree of flaking DIN EN ISOPaints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 6: Resistance to Sulphur Dioxide: Endorsement notice The text of ISO If you are more concerned with the effect of sunlight, moisture and temperature on the actual surface coating, please refer to our Durability tests.

If it is necessary to suspend specimens, the ein used shall not be metallic but shall be synthetic fibre, cotton thread or other inert insulating material. In practice this means that the test object must be capable of fitting inside a cube with mm sides. Assessment of degree isk blistering DIN EN ISOPaints and varnishes — Evaluation of degradation of coatings — Designation of dln and size of defects, and of intensity of uniform changes in appearance — Part 3: Adjust the pH using the procedures described in 3.

DIN EN ISO (en)_百度文库

D normative Required supplementary information for testing test panels with? The test cabinet shall be filled with isp specimens of inert materials such as plastic or glass during the verification procedure. The test duration is 24 h. After this procedure, the specimens to be tested are placed in the cabinet. It is especially useful for testing decorative coatings of copper? NOTE During permanent operation, a reasonable time period between two checks of the corrosivity of the apparatus is generally considered to be 3 months.

  LEY 1095 HABEAS CORPUS PDF

For chemical cleaning, use a solution with a mass fraction of 20?

DIN EN ISO – 盐雾测试_百度文库

We did tests of our products under ISO Assessment of degree of blistering ISO The upper parts of the cabinet shall be designed so that drops of sprayed solution formed on its surface do not fall on the specimens being tested. In addition, for quality control purposes, comparison can be made between specimens coated with the same coating. Assessment of degree of delamination and corrosion around a scribe ISO?

C describes how test panels with organic coatings are to be prepared for testing. Unless otherwise agreed, the scratch shall have either parallel sides or an upwards? Report the result obtained for each specimen tested and, when appropriate, the average result for a group of replicate test specimens. Penknives should not be used. NOTE For the efficient dissolution of the corrosion products during the immersion step, it is important that the solution is kept stirred.

The test duration shall be 48? New AkzoNobel site strengthens leading powder coatings position in China 25th January Read more.

One or two scribe marks may be applied. Remove the corrosion products by mechanical and chemical cleaning as described in ISO? I suggest that you send some parts out for testing according to the ISO standard to see if they meet the spec. This is a less severe version of the standard salt spray tests and is generally regarded as giving a better correlation with outdoor exposure results. They are not intended to be used for comparative testing, to rank ieo materials relative to each other with respect to corrosion sio.

  DOCTOR ZHIVAGO SCREENPLAY PDF

General introduction and designation system DIN EN ISOPaints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 2: Thoroughly clean the reference specimens with an appropriate organic solvent such as a hydrocarbon with dn boiling point between 60? The dn of the reference test specimens may be protected by the adhesive tape as well 5.

Assessment of degree of blistering ISO?

Unless otherwise specified, the back and edges of the panel shall be coated with the coating system under test. How to treat specimens ios testing should, in line with good engineering practice, be included in the test specification.

Equivalence between ASTM B-117 vs. ISO 9227 NSS

Annex D gives supplementary information needed for testing of test panels with organic coatings. Resistance to Cyclic Salt Spray. The market for agricultural, construction and earthmoving equipment remains attractive, according to a recent artic… https: The pressure should be rin Carry out the cleaning in a vessel full of solvent.

Avenue Marnix 17, B Brussels? Possible changes in pH may result from loss of carbon dioxide from the solution when it is sprayed. To determine the corrosivity of the tests, reference? AkzoNobel signs cooperation agreement on bio-based polymer technology with Itaconix 2nd February Read more.

After each stripping, thoroughly clean the reference specimens at ambient temperature with water, then with ethanol, followed by drying.

No Comments

Categories: Politics