AX 650TF PDF
The AX/TF Series of long range photoelectric detectors with selectable beam frequencies. The selectable beam frequencies can be used to avoid. The Optex AXTF is an outdoor 4-channel select dual beam photoelectric detector featuring a detection range and a form C relay output. Searching for a low cost Photoelectric Detector solution? The Optex AXTF is a great Photoelectric Detector within our Photoelectric Detectors product line at.
|Published (Last):||14 December 2018|
|PDF File Size:||10.32 Mb|
|ePub File Size:||13.62 Mb|
|Price:||Free* [*Free Regsitration Required]|
Does the relay open when the LED Indicator activates? The power line is short circuited or grounded. There are plants, trees or debris that may block the beam during windy conditions. The detector shall contain 4 selectable beam frequencies 4 channels to avoid unwanted crosstalk that can occur when using multiple photo-beams for long distance or beam stacking applications.
Power wires should not exceed the following lengths. Skip to main content. And pull out the wire through the wiring hole og the Mounting plate, attach the mouting plate to the U-Shape bracket with screw.
Installation and user manual for the FX range of fire panels 1, 2, 4 and 8 zone panels Contents Panel installation 3 Panel connections 3 Wiring connection drawings 4 Panel facilities 6 Installation check. Adjust the installation height. Use the HU-1 heater unit. This design shall allow beam passage even when the cover is completely frosted over. Wall or Pole Weight Bad wiring or corroded splices. Read and become familiar. Change footing, pole or structure to insure a stable mounting surface.
To make this website work, we log user data and share it with processors. Remove the power wires from Power supply’s output terminals.
If so, the installation height is not proper. General 1 Detection range and installation height. The covers are very dirty or dusty. Go to page 650t, see trouble shooting procedure number False activations Check alignment voltage from Monitor Jack. Suitable for detecting human bodies in hazardous area. Four M8 wall fixings 5. This manual uses recycledpaper.
Move the beams to 650hf the rising or setting sun. Call Technical Support if you are unsure of the proper shielding techniques. Turn mirror base by hand to obtain the highest alignment level. Adjust the interruption time, change the installation height or move the beams in order to avoid perching birds within the beam’s path.
Change the lay-out of the beams or call Technical Support for further advice. It will wx when the environmental conditions clear. Like the sun, More information. The OilTector More information. The case aax include easy wiring knockouts, and 4 pieces of Pole -mounting Bracket.
No false alarm shall occur within these operating condition. A different type of beam should not reach the receiver. Failure to follow the safety rules and other basic safety precautions may result in serious More information.
STEP1 Rough alignment by view finder Looking through the view finder, locate the other detector in the center of the sights by adjusting vertically and horizontally. The detector shall feature frost and dew protection. Safety design for category 2.
If you are unsure 650tt the proper wire gauge, call Technical Support. Can easily obtain maximum optical alignment by checking the voltage from this jack. FM Remote-Control Receiver 2. Always read and follow the manufacturer s instructions for the equipment you are connecting this product More information.
After the final adjustment are made on the upper mirrors carefully without moving morror remove “Beam Blocking Tool” from the lower mirrors and place them on the upper mirrors of both the Transmitter and Receiver.
One large allen key 2. Safety Operation Maintenance More information. Check for shorts, opens grounds and high resistance values or the alarm circuit wires.
Optex Ax-650tf Photoelectric Motion Sensor Set Transmitter and Receiver
YES Power cables may be too long for the gauge being used. Replace or repair as necessary The control panel may be malfunctioning, call the control panel manufacturer. The Detector features More information. This will insure proper beam alignment. The detector shall contain D. The alarm output shall be capable of handling 28 Volts DC, 0.
OPTEX AXTF | ADI
Beam interruption times exceeding 70 msec do not comply with the requirements in UL Make fine adjustment by turning “Fine Adjustment Screw”. Then check again that the voltage from monitor jack is more than about 5. When stacking beams or installing more than one set as the same area.