ASTM D1248 PDF

Buy ASTM D SPECIFICATION FOR POLYETHYLENE PLASTICS EXTRUSION MATERIALS FOR WIRE AND CABLE from SAI. This standard is issued under the fixed designation D ; the 1 This specification is under the jurisdiction of ASTM Committee D20 on. ASTM D Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable.

Author: Nebei Toshura
Country: Ecuador
Language: English (Spanish)
Genre: Sex
Published (Last): 1 September 2005
Pages: 342
PDF File Size: 12.82 Mb
ePub File Size: 9.6 Mb
ISBN: 271-1-93803-341-1
Downloads: 50988
Price: Free* [*Free Regsitration Required]
Uploader: Dik

ASTM D Polyethylene Plastics Extrusion for Wire and Cable | Test Equipment

This asgm discussed in Practice D A superscript epsilon e indicates an editorial change since the last revision or reapproval. Conditioning and test conditions shall be as speci? E5 12 [] —75 For information regarding molding and extrusion materials, see Specification D Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Deleted the existing paragraphs ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. For all materials to asttm conditioned for electrical testing, conditioning shall comply with the requirements of the standard test methods for electrical testing. Therefore, the effects of the exposures described in Note 3—See Guide D and 3.

ASTM D1248 Polyethylene Plastics Extrusion for Wire and Cable | Test Equipment

This standard asm not purport to address all of the safety concerns, if any, associated with its use. For such materials, the milling procedure described in J5 22 [] —75 It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  HACIA UN MUNDO SIN POBREZA YUNUS PDF

Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

For information regarding plastic pipe materials, see Speci? This abstract is a brief summary of the referenced standard.

Give our test engineers a ast, today for help configuring the best test machine d148 accessories according to your standard. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications.

Irradiance at the control point shall be maintained at 0. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Category 1,Category 2, Category 3,Category 4, and Category 5.

  BERTA BRASLAVSKY PRIMERAS LETRAS O PRIMERAS LECTURAS PDF

Test specimens over 7 mm in thickness shall be conditioned for 88 h. Test results for specimens that break outside the gage-marks after extensive cold drawing need not be discarded unless the break occurs between the contact surfaces of a grip. The melt viscosity of polyethylene plastics, in common axtm that of most high polymers, is non-Newtonian, that is, dependent on the rate of shear. ASTM D refers to a number of ASTM mechanical testing standards to determine physical characteristics of polyethylene plastic extrusion wire and cable.

Work Item s – proposed revisions of this standard. Any other size two-roll laboratory mill may be used provided the charge is adequate to maintain a uniform rolling bank on the rolls and to furnish sufficient material for test specimens.

The degree of departure zstm Newtonian behavior depends on the nature and molecular constitution of the individual sample.

Classes A, B Water immersion stability 8 [] — Active view current version of standard.

Sampling for inspection and testing shall be carried out in accordance r1248 the recommendations of Practice D For information regarding plastic pipe materials, see Specification D It is not the function of this speci?

No Comments

Categories: History